Description
Note: It’s diy kits. Need to solder by yourself.
The package does not include battery.
Due to the light and screen setting difference the item’s color may be slightly different from the pictures.
Please allow slight dimension difference due to different manual measurement.
Description:
LM393 comparing two photosensitive resistance when the imbalance (eg side pressure runway black) immediately control side of the motor stops rotating the other side of the motor rotation acceleration so that the car modification direction return to the right direction the whole process is a closed loop therefore rapid and sensitive control.
With the aim of simplifying the complex principle we first have a by digital circuit to the intelligent tracking car in the assembly process we could not only familiar with the mechanical principle gradually can learn to: photocell a voltage comparator a motor drive circuit and other related electronic knowledge.
Photosensitive resistance device:
This is light-sensitive resistance it can detect the external light intensity the stronger the outside light photosensitive resistance resistance is small the outside light weaker resistance is greater when the red LED light projected on a white and black runway because reflection rate is different the resistance value of the light-sensitive resistance will occur obvious difference for subsequent circuit control.
LM393 comparator integrated circuit:
LM393 is a dual voltage comparator integrated circuit which consists of two independent precision voltage comparator. its role compare the two input voltage based on the level of two input voltage change the level of output voltage. The output has two states: close to open or close to the low level LM393 using open collector output so it is necessary to add the pull resistance to output high level.
DC motor with gear reduction:
DC motor drive the car needs to slow down otherwise to speed up the car then ran too fast not control and the deceleration torque is too small and could not run up. We specialize in custom of this type of motor is integrated with the reduction gear and greatly reducing the manufacture difficulty is very suitable for our use.
LM393 comparing two photosensitive resistance when the imbalance (eg side pressure runway black) immediately control side of the motor stops rotating the other side of the motor rotation acceleration so that the car modification direction return to the right direction the whole process is a closed loop therefore rapid and sensitive control.
Assembly steps:
The first step: circuit part of the basic welding
The welding circuit part is relatively simple the welding sequence according to the element height from low to high the first 8 resistance welding welding must use a multimeter to confirm whether the proper welding resistance polar components such as transistors green lights definitely clear electrolytic capacitor polarity as reference element we are photo welding welding capacitor short is the negative side of the insertion pin PCB screen printing shadow green welding LED note long pin is positive and the welding is not too long or easy bad welding D4 D5 R13 R14 can temporarily do not weld the integrated circuit chip can be inserted preliminary after completion of welding check carefully prevent be negligent.
Second step: mechanical assembly
The universal wheel screw is inserted into the PCB hole and screwed into the universal wheel nut and a universal wheel. the battery box is stuck on the PCB by the double adhesive tape the lead wire passes the PCB reserved Kong Han received PCB the red line is connected with the 3 V positive power supply and the yellow line is connected to the ground.
Mechanical part and assembly can be mounted first wheels wheel consists of three pieces of black acrylic round tablets assembly prior to exposing protective film the inside of the wheel center hole grows circular hole middle of the round plate diameter is relatively small lateral wheel piece center hole Shiyuan with two screw nuts fixed set good three round tablets and black self-tapping screws fixed on the rotating shaft of the engine. Finally the silicone rubber tire sleeve on the wheel. Lead connection lead wire of the motor and the wheel assembly is the use of the glue on the PCB making position attention wheels and the PCB edge retaining sufficient clearance the motor leads are soldered to the PCB. Note that adequately longer lead to avoid the motor rotation direction error is convenient for changing the lead wire of the order.
The third step: the installation of opto-electronic circuits
Photosensitive resistance and light-emitting diode (attention polarity) is the reverse installed on the PCB and the ground distance of about 5mm the distance between the light-sensitive resistance and light-emitting diode is also about 5mm. Finally can pass electrical test.
The fourth step: Vehicle debugging
In the battery box in 2 AA batteries switches to dial in the “on” the car driving right reverse is traveling along the direction of the universal wheel if hold the left side of the photosensitive resistance the car to the right of the wheel rotation Keep to the right of photosensitive resistance the left side of the car wheel must turn if car travel back can exchange connection of two motors at the same time. as one of the normal back on the other side as long as the exchange of the rear of the motor can be wiring.
Package Included:
1* D2-5 Smart Robot Car Kits
Circuit diagram:
“
You may also like:
Bluetooth Speaker Kit with FM Radio: 87.5-108MHZ Soldering Project for Electronics Practice
TJ-56-428 4-Digit Digital Clock Kit: Acrylic Shell Alarm Clock for Soldering Practice
FM Radio Electronic Kit: Adjustable Frequency 87-108MHz with Digital Display for Soldering Practice
TOYAN FS-L200AC Methanol Engine Electronics Kit Advanced High Performance Metal Twin Cylinder Engine Model Starter Kit
M55Stack Cardputer Kit with M5StampS3 – Complete Development Solution
Colorful RGB Bluetooth Soldering Kit: 32-Layer LED Music Spectrum Cube
ELEGOO Owl Smart Robotic Car Kit – Nano V4 Line Tracking Arduino
INJORA Brass & Aluminum Complete Portal Axles 1/18 RC Crawler Redcat Ascent-18
BMR-X EVO ARR Version 1:24 Rwd Rc Drift Car Equipped New Top Electronics(BMRX-EVO-ARR)
BMR-X PRO Purple ARR Version 1:24 Rwd Rc Drift Car Equipped New Top Electronics(BMRX-PRO-ARR)
4drc l1 fighter drone 1080p hd rc quadcopter single rotor four-channel anti-collision intelligent electric helicopter
HS-02A-B-100W – FNIRSI HS-02 Smart PD 100W Portable Soldering Iron Kit
Reviews
There are no reviews yet.